まえがき
1. 開催WG、日時
2. 開催場所
3. 出席者
4. 議事
1. TC 188 N 118 Report of Meeting held in Oslo, Norway, 5, April 1999
2. TC 188/WG 18 N XXX ISO/CD 1 2215-5.19, Design pressures, allowable stresses, scantling determination
1 Scope
2 Normative
3 Terms and definitions
4 Symbols
5 Design pressure
5.1 Bottom design pressure
5.1.1 Motor craft bottom pressure
5.1.2 Sailing craft bottom pressure
5.2 Side structure, design pressure
5.2.1 Limit of bottom and side pressure
5.2.2 Vertical extent of side pressure
5.2.3 Vertical correction factor
5.2.4 Design pressures
5.3 Deck, design pressure
5.4 Watertight bulkheads and integral tank bulkheads, design pressure
5.4.1 Watertight bulkheads
5.4.2 Integral tank bulkheads
5.4.3 Wash plates
5.4.4 Collision bulkheads
5.4.5 Gastight bulkheads
5.4.6 Non-watertight or partial bulkheads
5.4.7 Transmission of pillar loads
6 Design stresses
6.1 Shell
6.1.1 Plating
6.1.2 Framing
6.1.3 Core
6.2 Bending stiffness coefficient for FRP construction
7 Basic scantling equations
7.1 Plating
7.1.1 FRP single skin, aluminium alloy, steel construction
7.1.2 Sandwich construction
7.2 Internal stiffening members
7.2.1 Section modulus
7.2.2 Moment of inertia
7.2.3 Proportions
7.3 Structural bulkheads
8 Mechanical properties for calculation
8.1 FRP laminates
8.1.1 Tested laminates
8.1.2 Non tested laminates
8.1.3 Determination of glass content
8.1.4 Calculation of mechanical properties
8.2 Metals
3. TC 188/WG 18 On scantling equation for a thickness of plate based on the large deflection
4. TC 188/WG 18 N 121 Annex A Simplified calculation method for motor craft scantling
5. TC 188/WG 18 Comment for Simplified calculation method
6. TC 188/WG 18 Scantling study committee at JCIO
7. TC 188/WG 18 N 2.3 ISO/WD 12215-2.1, Materials
1 Scope
2 Normative reference
3 Sandwich structure
3.1 Structural requirements
3.2 Material requirements, general
3.3 Material requirements, specific
3.3.1 Rigid expanded foam
3.3.2 End grain balsa
3.3.3 Other core materials
3.4 Manufacturing requirements
3.4.1 Sandwich construction using female moulds
3.4.2 Sandwich construction with male mouldsplugs
4 Embedded materials
4.1 General requirements
4.2 Specific requirements
Annex A (normative) Mechanical properties of some sandwich core materials
8. TC 188/WG 5 ISO/DIS 10088, Permanently installed fuel systems and fixed fuel tanks
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
5 Fuel tanks
5.1 Materials, design and marking
5.2 Testing
5.3 Installation
6 Fuel pipes, hoses, connections and accessories
6.1 Fuel fill lines
6.2 Vent lines
6.3 Fuel distribution lines and fuel return lines
6.4 Hose fittings and hose clamping
6.5 Valves
6.6 Fuel filters
Annex A (normative) Pressure testing
Annex B (normative) Fire resistance testing
Annex C (normative) Fuel tank material, design and marking
Annex D (informative) Inspection of fuel system
9. TC 188/WG 5 Report of voting on ISO/DIS 10088
10. TC 188 N 400 ISO/CD 16147, Inboard-mounted diesel engine fuel and electrical systems components
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Engine fuel system components
5.1 High pressure pipes and injectors
5.2 Low pressure fuel lines
5.3 Fuel filters
5.4 Starting aids
6 Engine electrical systems and components
6.1 D.C. installations
6.2 Cranking motors
6.3 Alternators
6.4 Wiring and connections
6.5 Relays, fuse boxes and electronic control modules (ECMs)
6.6 Integral and remote stop solenoids systems
Bibliography
11. TC 188 N 419 Annex COMMENTS RECEIVED ON ISO/CD 16147 (N 400)
12. TC 188 N 411 Permanently installed petrol and diesel fuel tank
1 Scope
2 Normative references
3 Terms and definitions
4 General
5 Materials
5.1 Metallic tanks
5.2 Non-metallic tanks
6 Design
7 Tests
7.1 Tightness test
7.2 Hydraulic pressure/strength test
7.3 Pressure-impulse test for petrol tanks
7.4 General fire resistance test of non-metallic tanks
7.5 As installed fire resistance test of non-metallic tanks
8 Marking
13. TC 188 N 431 Annex Comments received on the NWIP in doc. ISO/TC 188 N 411
14. TC 188/WG 5 AMENDMENTS TO ISO/DIS 15584, Inboard petrol engines- Engine-mounted-fuel and electrical component
1 Scope
3 Terms and definitions
4 General
5 Engine fuel system components
5.1 General requirements - Piping, hoses, pumps, filters and their connections
5.2 Carburettors and/or throttle bodies
5.3 Conditioning procedure
5.4 Leakage test
6 Engine electrical systems and components
6.1 General requirements
6.2 Ignition distributors
6.3 High-tension (secondary) ignition cable assemblies - Dielectric leakage test
Bibliography
15. TC 188/WG 5 Report of voting on ISO/DIS 15584
16. TC 188/WG 5 N ?? ISO/WD 7840, Fire-resistant fuel hoses
1 Scope
3 General requirements
4 Nominal bore
5 Physical tests on finished hose
5.1 Bursting pressure
5.2 Suction resistance test
5.3 Volume change in liquid C
5.4 Mass reduction in liquid C
5.5 Fire resistance
5.6 Effect of ozone
5.7 Fuel permeation
5.8 Cold flex test
5.9 Abrasion test - 38 mm and larger fuel fill hose with helical wire imbedded reinforcement
5.10 Dry heat resistance
5.11 Oil resistance test
5.12 Adhesion test
6 Designation and marking
6.1 Designation
6.2 Marking
Annex A (normative) Fire test
Annex B (normative) Fuel permeation test(or equivalent test method)
17. TC 188 N 421 Results of voting on ISO/CD 15083
